HD77 – Pliolite Heavy Texture Coating

HD77HD77 – Pliolite Heavy Texture Coating

PRODUCT INFORMATION
HD77 Pliolite Heavy Texture Coating is a premium quality, long life high build coating formulated for exterior use on cement rendering and concrete surfaces. It provides a self- stabilizing textured matt finish that has excellent adhesion to previously painted and porous surfaces.

Pack Size
25kg Drum
Pallet QTY
30 Units
Finishing Tool
R1 Roller
Suitable Substrate
Suitable Wethertex™ primer / Base Coat
Water Down
Max 2% – with S62 Diluter
Coverage
10 M² per unit
Application Temperature
1˚c – 25˚c
Humidity Requirement
Less than 95%

PREPARATION
On new base coat HD77 Pliolite Heavy Texture Coating can be applied directly to a suitably prepared substrate. For re-furbishment projects, make good cracks and structural defects and remove any loose flaking and brittle material. If there is evidence of organic growth, power wash to remove & apply Wethertex Fungicidal wash in accordance with instructions. Then ensure that the substrate has been primed or base coated with a suitable product for the substrate type. Beads and expansion joints should be included as required by the substrate and BS standards and carried through all applied materials. When required apply Wethertex GRC Render as a base coat. Specifications for mixed or unusual substrates are available on request.

PRIMING
Suitable Wethertex Primer or Base Coat.

MIXING
HD77 Pliolite Heavy Texture Coating is supplied ready to use, but may need re-mixing using a suitable paddle mixer to regain correct consistency for application.

Note: HD77 may stiffen on standing. Re-mix the product to regain a workable consistency but do not add more
than 5% S62 Diluter.

APPLICATION
To avoid dampness and discoloration application should be avoided below DPC or within 150mm of ground level.
Trowel – Apply smoothly and evenly to a thickness of about 1.5 – 2.5mm, with the help of a steel trowel.
To create the texture – Load a lamb’s wool roller generously and apply with minimum pressure in short slow strokes covering small areas at a time. Move the roller from top to bottom, left to right or right to left to create desired effect.
Specification Clauses relating to this product can be found in NBS Section M20 Rendering. BS 5262 Code of Practice for External Rendering and BS 8000-10 must be followed.

STORAGE
When stored unopened in a dry place at temperatures above 5oC, shelf life is 12 months from date of manufacture.

TOOL CLEANING
All equipment must be washed with white spirit immediately after use. Waste material should not be emptied into drainage systems.

HEALTH & SAFETY INSTRUCTIONS
For further information, please request the material safety data sheet for this product.

IMPORTANT INFOMATION
The weather conditions for application and drying are critical. Do not apply if any of the following conditions are likely to arise during –
or in the first 24 hours following application:
o If frost is forecast, or in excessive wet conditions
o When Relative Humidity is above 95%
o In temperatures below +1ºC or above +25ºC
o If the elevation is in direct sunlight
o If the substrate is hot (at or above 30C) or below +1ºC
o Coverage rates are approx. and do not take into account wastage and uneven substrates

The render must be protected against heavy rain, direct sun or high wind in the first 24 hours after application. Sheeting the façade or the scaffold is advised to protect against this. For this particular product, if these parameters are not met, the product is at risk of, efflorescence and potential failure. It is the responsibility of the application contractor to manage and record the weather conditions during application and curing of the product.

To the best of our knowledge and belief, this information is true and accurate. However, as conditions of use of the product and the expertise of any labour involved are beyond our control, the end user must satisfy himself by prior testing that the product is suitable for his specific application if no spec has been provided for the project in hand. No responsibility can be accepted, nor any warranty given by our Representatives, Agents or Distributors. Products are sold subject to our Standard Conditions of Sale and the end user should ensure that he has consulted our latest literature.

Download HD77 Product Datasheet

Take a Look at Our Colours & Finish Options

19 beautiful pastel shades that will allow you to colour your building with a sympathetic approach to its surroundings.

Specification & Advice Service

We offer a full specification and technical servie for all approved contractors.

Approved Network of Quality Approved Contractors

With our wide network of carefully selected contractors we can put you in touch with someone in your area.

Wetherby Group

Dalton Industrial Estate, Dalton
North Yorkshire, YO7 3HE

Get in Touch

T+44 (0)1845 578555

F+44 (0)1845 578777

Esales@wetherbygroup.com

Awards & Accreditations
Copyright Wetherby GroupTM