AX1 – Pliolite Thin Coat Render

AX1 – Pliolite Thin Coat Render

PRODUCT INFORMATION

AX1 Pliolite Thin Coat Render is a premium quality, long life, trowel applied, ready to use, through-coloured, thin-coat render which is formulated based on Pliolite Resin technology. AX1 has excellent adhesion and breathability properties, and Pliolite technology has been proven to work effectively on properties for over 45 years. This product will not only fully waterproof your property and create a beautiful finish, but will also allow the building to breathe naturally due to its high vapour transmission rate. This in combination with the high adhesion benefits of Pliolite resins ensures that your property will be protected with the best quality wall coating technology available on the market.

Pack Size
25kg Drum

Finishing Tool
Plastic Float

Suitable Substrates
GRC Fibre Glass Reinforced Base Coat,
X71 Polymer Levelling Base Coat

Coverage
Approximately 10m2 per unit

Application Temperature
-10ºC – 25ºC

Humidity
Less than 95%

PREPARATION
All surfaces must be sound, clean, dry and free of any material which may impair adhesion. Do not apply to shiny surfaces. Scaffolding must be independently tied to allow for uninterrupted application. Any faults in the structure – particularly those which may lead to moisture penetration – must be rectified. Substrate should be prepared with primer. Mask around the areas where material is to be applied. Always apply a test panel for client, specifier, main contractor or other interested party to approve before starting the main body of the work.

PRIMING
Use Wethertex PP1 Primer prior to AX1 over GRC, X71 or a suitable basecoat.

MIXING
AX1 Pliolite Thin Coat Render is supplied ready to use but always ensure that the material has been mixed using a drill with suitable whisk prior to application.

APPLICATION
DO NOT apply to a wet substrate under any circumstances.
To maintain colour consistency, panels should be completed in sequence around the building. To avoid dampness and discolouration rendering should be avoided below DPC or within 150mm of ground level. To apply the material, use a stainless steel trowel or suitable spray equipment depending on the grain size. Use the size of the aggregate to gauge the thickness of the render when applying to the substrate ie. AX1 Pliolite Thin Coat Render 1.5mm = thickness 1.5mm. Once the render is applied, finish with a plastic float working the material in small circular motions, this will create the natural random finish.

STORAGE
When stored unopened in a dry place at temperatures above 5ºC, shelf life is 12 months from the date of manufacture.

TOOL CLEANING
All equipment must be washed with clean water immediately after use. Waste material should not be emptied in the drainage systems.

HEALTH & SAFETY INSTRUCTIONS
For further information, please request the material safety data sheet for this product.

IMPORTANT INFORMATION
The weather conditions for application and drying are critical. Do not apply if any of the following conditions are likely to arise during, or in the first 24 hours following application.

• If frost is forecast, or in excessive wet conditions
• Relative humidity is above 95%
• In temperatures below -10ºC or above 25ºC
• If the elevation is in direct sunlight
• If the substrate is hot (at or above 30ºC)

Coverage rates are approximate and do not take into account wastage and uneven substrates.

The product must be protected against heavy rain, direct sun or wind in the first 24 hours after application. Sheeting the façade or the scaffold is advised to protect against this. For this particular product if these parameters are not met polymer film damage, wash off, discolouration and potential failure can occur. It is the responsibility of the application contractor to manage and record the weather conditions during application and curing of the product.

To the best of our knowledge and belief, this information is true and accurate. However, as conditions of use of the product and the expertise of any applicator involved are beyond our control, the end user must satisfy themselves by prior testing that the product is suitable for the specific application if no specification has been provided for the project in hand. No responsibility can be accepted, nor any warranty given by our Representatives, Agents or Distributors. Products are sold subject to our Standard Conditions of Sale and the end user should ensure that they have consulted our latest literature.

Take a Look at Our Colours & Finish Options

19 beautiful pastel shades that will allow you to colour your building with a sympathetic approach to its surroundings.

Specification & Advice Service

We offer a full specification and technical servie for all approved contractors.

Approved Network of Quality Approved Contractors

With our wide network of carefully selected contractors we can put you in touch with someone in your area.

Wetherby Group

Dalton Industrial Estate, Dalton
North Yorkshire, YO7 3HE

Get in Touch

T+44 (0)1845 578555

F+44 (0)1845 578777

Esales@wetherbygroup.com

Awards & Accreditations
Copyright Wetherby GroupTM