PP1 – Pre-prep Wash Coat Primer

PP1 pliolite primerPP1 – Pre-prep Wash Coat Primer

water-repellent
extra-coverage
low-temp-application
roller-and-brush-application
Highly-polymer-modified

DESCRIPTION
PP1 Prep-Wash Coat Primer is a ready mixed, flexible through coloured penetrating primer to control suction and ensure good key for finish coating.

Pack Size
10 Litres
Pallet QTY
30 Units
Application Tool
Brush, Roller or Spray
Suitable Substrate
TK11, GRC, X71, Bonded Paint, Dash,Roughcast, Render
Drying Time
3 – 24 Hrs @ 25 – 5˚c
Coverage
85 M² per 10 Litres
Application Temperature
1˚c – 25˚c for a min of 24 hrs
Humidity Requirement
Less than 85% for a min of 24 hrs

PREPARATION
All surfaces must be sound, clean, dry and free of any material which may impair adhesion. Scaffolding must be independently-tied to allow for uninterrupted application. Any faults in the structure, particularly thosewhich may lead to moisture penetration, must be rectified.
MIXING
PP1 Prep-Wash Coat Primer is supplied ready to use, but may need re-mixing using a suitable paddle mixer to regain correct consistency for application.
APPLICATION
By roller – submerse the roller totally in the primer to ensure that the roller is fully loaded with material to allow even application without spreading too thinly.
Specification Clauses relating to these products can be found in NBS Section M20 rendering. BS 5262 Codeof Practice for External Rendering and BS 8000-10 must be followed

STORAGE
When stored unopened in a dry place at temperatures above 5oC, shelf life is 12 months from date of manufacture.

TOOL CLEANING
All equipment must be washed with white spirit immediately after use. Waste material should not be emptied into drainage systems.

HEALTH & SAFETY INSTRUCTIONS
For further information, please request the material safety data sheet for this product.
IMPORTANT INFOMATION
The weather conditions for application and drying are critical. Do not apply if any of the following conditions are likely to arise during –
or in the first 24 hours following application:
o If frost is forecast, or in wet conditions
o When Relative Humidity is above 85%
o In temperatures below +1ºC or above +25ºC
o If the elevation is in direct sunlight
o If the substrate is hot (at or above 30C) or below +1ºC
o Coverage rates are approx. and do not take into account wastage and uneven substrates
The product must be protected against heavy rain, direct sun or wind in the first 24 hours after application. Sheeting the façade or the scaffold is advised to protect against this. For this particular product if these parameters are not met polymer film damage, wash off, discoloration and potential failure can occur. It is the responsibility of the application contractor to manage and record the weather conditions during application and curing of the product.
To the best of our knowledge and belief, this information is true and accurate. However, as conditions of use of the product and the expertise of any labour involved are beyond our control, the end user must satisfy himself by prior testing that the product is suitable for his specific application if no spec has been provided for the project in hand. No responsibility can be accepted, nor any warranty given by our Representatives, Agents or Distributors. Products are sold subject to our Standard Conditions of Sale and the end user should ensure

Further Information

Download PP1 Product Datasheet

Take a Look at Our Colours & Finish Options

19 beautiful pastel shades that will allow you to colour your building with a sympathetic approach to its surroundings.

Specification & Advice Service

We offer a full specification and technical servie for all approved contractors.

Approved Network of Quality Approved Contractors

With our wide network of carefully selected contractors we can put you in touch with someone in your area.

Wetherby Group

Dalton Industrial Estate, Dalton
North Yorkshire, YO7 3HE

Get in Touch

T+44 (0)1845 578555

F+44 (0)1845 578777

Esales@wetherbygroup.com

Awards & Accreditations
Copyright Wetherby GroupTM