X71 One-Coat Base

X71 – Base Coat AdhesiveX71

X71 One-Coat Base in a highly polymer modified high performance cement based waterproofing base coat which has excellent workability and finishing time properties the No 1 all round product for multiple substrates.  This product can be applied by hand or spray in low temperatures and used as a base coat ready to receive a suitable finish coating.

Pack Size
25kg bag
Pallet QTY
40 bags
Finishing Tool
Sponge Float or Brush
Substrate Prime
S10
Suitable Substrate
Concrete, Clay,Light Weight Block, and Brick
Water Demand
Approx. 4.5Ltr per 25kg bag
Pot Life
1 Hr +
Ready to Finish
8 to 2 Hr @ 3 -25˚c
Coverage
1.5 M² per bag @ 10mm thick
Application Temperature
3˚c – 25˚c

 

APPLICATION
To avoid dampness and discoloration rendering should be avoided below DPC or within 150mm of ground level.

X71 One-Coat Base should be applied in a one-coat 2-pass operation to a thickness of 10-15mm.
10mm Flat Finish – Ready to receive a coating
The 1st pass should be applied to the primed substrate with a stainless steel trowel or spray pump, and for ease of application a serrated feather edge and finishing spatula will help. Apply the 1st pass to approx 5mm thick with fibre-reinforcing mesh included in the 1st pass ensuring that the mesh is overlapped 100mm at the mesh joints. Additional fibre-reinforcing mesh stress patches of 500 x 500 mm should be added at all openings:
i.e., windows and doors, and also window reveals for additional substrate stress protection. The 2nd pass should then be applied to approx 5mm thick wet on wet to the 1st pass levelled flat and should be left to pick up for 2 to 8 hrs and then be wet sponge float finished flat and allowed to set. Total thickness = 10mm
15mm Flat Finish – Ready to receive masonry paint
The 1st pass should be applied to the primed substrate with a stainless steel trowel or spray pump, and for ease of application a serrated feather edge and finishing spatula will help. Apply the 1st pass to approx 8mm thick with fibre-reinforcing mesh included in the 1st pass ensuring that the mesh is overlapped 100mm at the mesh joints. Additional fibre-reinforcing mesh stress patches of 500 x 500 mm should be added at all openings:
i.e., windows and doors, and also window reveals for additional substrate stress protection. The 2nd pass should then be applied to approx 7mm thick wet on wet to the 1st pass levelled flat and should be left to pick up for 2 to 8 hrs and then be wet sponge float finished flat and allowed to set. Total thickness = 15mm
Specification Clauses relating to this product can be found in NBS Section M20 Rendering. BS 5262 Code of Practice for External Rendering and BS 8000-10 must be followed.

STORAGE
When stored unopened in a dry place at temperatures above 5oC, shelf life is 12 months from date of manufacture.

TOOL CLEANING
All equipment must be washed with clean water immediately after use. Waste material should not be emptied into drainage systems.

HEALTH & SAFETY INSTRUCTIONS
For further information, please request the material safety data sheet for this product.
IMPORTANT INFOMATION
The weather conditions for application and drying are critical. Do not apply if any of the following conditions are likely to arise during –
or in the first 24 hours following application:
o If frost is forecast, or in excessive wet conditions
o When Relative Humidity is above 95%
o In temperatures below +3ºC or above +25ºC
o If the elevation is in direct sunlight
o If the substrate is hot (at or above 30C) or below +3ºC
o Coverage rates are approx. and do not take into account wastage and uneven substrates
The render must be protected against heavy rain, direct sun or wind in the first 24 hours after application. Sheeting the façade or the
scaffold is advised to protect against this. For this particular product, if these parameters are not met, the product is at risk of, efflorescence
and potential failure. It is the responsibility of the application contractor to manage and record the weather conditions during
application and curing of the product.
To the best of our knowledge and belief, this information is true and accurate. However, as conditions of use of the product and the expertise
of any labour involved are beyond our control, the end user must satisfy himself by prior testing that the product is suitable for his
specific application if no spec has been provided for the project in hand. No responsibility can be accepted, nor any warranty given by
our Representatives, Agents or Distributors. Products are sold subject to our Standard Conditions of Sale and the end user should ensure
that he has consulted our latest literature.

Further Information

Download X71 Product Datasheet

Take a Look at Our Colours & Finish Options

19 beautiful pastel shades that will allow you to colour your building with a sympathetic approach to its surroundings.

Specification & Advice Service

We offer a full specification and technical servie for all approved contractors.

Approved Network of Quality Approved Contractors

With our wide network of carefully selected contractors we can put you in touch with someone in your area.

Wetherby Group

Dalton Industrial Estate, Dalton
North Yorkshire, YO7 3HE

Get in Touch

T+44 (0)1845 578555

F+44 (0)1845 578777

Esales@wetherbygroup.com

Awards & Accreditations
Copyright Wetherby GroupTM